|Features:||Run Speed Adjustable, Battery Supported, Maitenance Free, Free Debugging||Operation Time:||0.6,0.9,3,6sec|
|Protection System(IP):||IP55||Rated Power:||0.6s(400W), 0.9S(200W)|
|Product Name:||Heavy Duty Wonsun 0.9S High Speed Gate Toll Barrier Gate 24V DC Motor LED Arm||Motor:||Servo Motor|
LED Arm toll boom barrier,
0.9S toll boom barrier,
LED Arm Toll Barrier Gate
Heavy Duty Wonsun 0.9S High Speed Gate Toll Barrier Gate 24V DC Motor LED Arm
DZ-138 barrier gate specifications:
|DZ-138 barrier gate||V06T||V09T|
|Max Boom Length and Diameter||2500mm, Ф75mm||3000mm, Ф75mm|
|Machine Case||Varnished 2.0mm steel plate||Varnished 2.0mm steel plate|
|Machine Case Size(W*D*H)||342*312*959mm||342*312*959mm|
|Operating Temperature Range℃||-45℃~+85℃||-45℃~+85℃|
|Driving Method||Servo motor||Servo motor|
Functions and Features
1. Gate automatically open when power off, no clutch design, no need human intervention. When power on,
gate automatically reset, restore to the gate closing state, truly unattended, fire safety standards. If special
requirement, manual operation is required when power off, operating arm open and close manually also can
be realized by setting up control board DIP switch, which ensure that the system can be used at any time.
2. The use of Single Compression Balance Spring device, good regulation, no noise, indefatigable, not easy to break, safe and reliable.
3. A variety of input and output modes can be selected, normally open normally closed are optional.
4. Arm opening angle can be adjusted from 60 to 90 degrees, 10 degrees resolution, suitable for eaves prominent place to install.
5. Closing speed can be adjusted.
6. Barrier gate up &down signal relay switch output.
7. Barrier gate running state: OK signal output indicating that the gate is working properly.
8. Barrier gate operation abnormal alarm signal output.
9. R&G Traffic light relay switch signal output.
10. External loop detector signal anti-smashing interface, infrared sensor signal anti-smashing interface.
11. Count mode interface.
12. Arm Open priority anti-smashing function. No matter the current gate in what state, the operator through the triple
push button, software or remote control to issue an open command, the gate will give priority to the implementation of the opening action.
1 General Security Information
The design, manufacture and testing of the barrier system are use of the "state-of-the-art" technology and can only be manufactured after the satisfaction of the strict safety and reliability of technical standards. Even so, if the barrier system is not properly operated, it will also cause danger to people and property. So this manual must be fully read and all of the safety information must be followed.
If the barrier system is improperly used or used for non-intended use, the
manufacturer will refuse to be responsible for the resulting consequences and will cancel the original quality assurance.
2 Suggested Application
High-speed barrier gates can only be used for toll stations for highways and trunk roads.
The medium barrier gates are designed to control the access roads, multi-storey car parking lot and other vehicular access routes for vehicle parking areas.
The controller is specifically designed to control the barrier gates.
It is not permissible to use these barrier gates for any other purpose.
Any changes and replacements to the barrier gates and the control components are prohibited.
3 Safety sign
The following symbols used in this instruction are used to indicate potential hazards and other safety information.
1. The internal wiring of the machine has been completed when it leaves the factory, please do not change it,
just connect the 220V power supply and the protective ground wire to work.
2. Traffic light interface: 2A12V voltage traffic light use.
3. Infrared anti-smashing interface: external infrared anti-radiation device, just connect the switch signal of the
4. Ground sense interface: support external ground sense. When using an external ground sensor, you only need to
connect the switch signal output by the ground sensor.
5. Parking system interface wire control interface: connect the switch signal of the system to this interface to control the barrier.
6. Starting limit and landing limit signal output: output COM/NO/NC switch signals to the system to inform the
current state of the barrier.
7. RS485 communication interface: PC software can be used to manage more than 15 barriers.
2nd servo motor components name
Q: Are you trading company or manufacturer ?
A: We are a professional barrier gate manufacturer.
Q: How long is your delivery time?
A: Generally it is 2-5 days if the goods are in stock. or it is 5-7 days if the goods are not in stock, it is according
to quantity.We can send it for you by DHL/Fedex/TNT/SEA/AIR or your requirments.
Q: How about payment terms our company provide?
A: T/T or Western Union.
Q: Do you provide free samples ?
A:No,we don't provide free samples. The MOQ of our products is 1pcs.
If you have any question, please contact us freely!
Sales representatives: Keira
Whatsapp: +86 18507481610
Contact Person: Keira
Tel: +86 185 0748 1610