10 Million Lifetime DC24V Servo Motor Toll Barrier Gate Parking Lot System Factory Price
DZ-138 specifications:
DZ-138 barrier gate
V06T
V09T
Max Boom Length and Diameter
2500mm, Ф75mm
3000mm, Ф75mm
Open/Close Time
0.6sec
0.9sec,2.5sec,4.5sec
Power Supply
24/100/240VAC,50/60Hz
24/100/240VAC,50/60Hz
Power Consumption
max.150W
100w
Machine Case
Varnished 2.0mm steel plate
Varnished 2.0mm steel plate
Machine Case Size(W*D*H)
342*312*959mm
342*312*959mm
Net Weight
43kg
42.6kg
Operating Temperature Range℃
-45℃~+85℃
-45℃~+85℃
Driving Method
Servo motor
Servo motor
Protection System(IP)
54
54
Insulation Class
F
F
Relative Humidity
≤90%
≤90%
Motor No-load Speed
3000r/min
3000r/min
Remote Control Distance
≤100m (open, sunny weather)
≤100m (open, sunny weather)
Output Torque
1.2N.M*140=160N.M
0.86N.M*140=120N.M
Running Noise＜
45dB
45dB
Surface Treatment
Outdoor metal powder electrostatic spraying
Outdoor metal powder electrostatic spraying
DZ Controller
Voltage(±10%)
100-240 volt
100-240 volt
Frequency(Hz)
50-60
50-60
Max Power Consumption(watt)
8
8
Fuse
F5AH
F5AH
Control Voltage
24V DC/max.3000mA
24V DC/max.3000mA
Input-end Number
8
8
Open Collector Output Number
2
2
Zero Level Reversal Relay Number
3
3
Operating Temperature Range℃
-45℃~+85℃
-45℃~+85℃
Protection System(IP)
20
20
Weight(gram)
450gram
450gram
Dimension
mm(L-W-H)
158*126*55
Functions and Features:
1. Gate automatically open when power off, no clutch design, no need human intervention. When power on,
gate automatically reset, restore to the gate closing state, truly unattended, fire safety standards. If special
requirement, manual operation is required when power off, operating arm open and close manually also can
be realized by setting up control board DIP switch, which ensure that the system can be used at any time.
2. The use of Single Compression Balance Spring device, good regulation, no noise, indefatigable, not easy to break, safe and reliable.
3. A variety of input and output modes can be selected, normally open normally closed are optional.
4. Arm opening angle can be adjusted from 60 to 90 degrees, 10 degrees resolution, suitable for eaves prominent place to install.
5. Closing speed can be adjusted.
6. Barrier gate up &down signal relay switch output.
7. Barrier gate running state: OK signal output indicating that the gate is working properly.
8. Barrier gate operation abnormal alarm signal output.
9. R&G Traffic light relay switch signal output.
10. External loop detector signal anti-smashing interface, infrared sensor signal anti-smashing interface.
11. Count mode interface.
12. Arm Open priority anti-smashing function. No matter the current gate in what state, the operator through the triple
push button, software or remote control to issue an open command, the gate will give priority to the implementation of the opening action.
13. Barrier with anti-collision protection function, when the vehicle hits the gate arm, arm can be swing out to avoid
damage to the vehicle, and barrier gate machine.
14. Delay closed selection function.
15. High-sensitivity arm auto reverse function (intensity can be adjusted).
16. Parking system interface.
17.RS485 or RS232 network communication control up &down interface (no need to install communication module)
18. Anti-collision alarm signal interface.
19. Adjustable speed port (from 0.9s to 10 s)
20. High-strength precision cast steel, industry moving parts beyond the industry quality
Program 1
The barrier gate can be controlled by two buttons and a short time signal impulse is enough to open barrier gate.
Wiring Connection: turn on the GND and COM,
Opening: turn on the 24V with UP
Closing: turn on the 24V with Down
Additional safety devices can be connected to the infrared signal input, vehicle detector signal input (loop detector).
Program 2
The barrier gate can be closed and opened by remote controller
Wiring Connection: connecting the receiver GND(COM) to COM of controller Remote-up is for opening and Remote-down is for closing.
Opening: connecting the receiver’s up level signal(5~24V) to the remote-up
Closing: connecting the receiver’s down level signal(5~24V) to the remote-down
Additional safety devices can be connected to the infrared signal input, vehicle detector signal input (loop detector).
If remote control receiver is non-electric relay signal, connection as bellows:
Wiring Connection: turn on the GND and COM,
Opening: turn on the +24V with Remote-up
Closing: turn on the +24V with Remote-down
Additional safety devices can be connected to the infrared signal input, vehicle detector signal input (loop detector).
FAQ:
1. When barrier finish closing, why does the arm open itself slowly?
the spring is too tight, you need release the spring a little, then test it again.
see whether the main crank touch the triangle tightly or not, if tightly, adjust it.
reset the balance position and the electrical limit switch.
2. Why does the controller panel operate with "Di Di Di" abnormal noises?
As for this, it means the resistance on controller board is broken, if you have professional tools to check,
then replace that broken resistance, if not, replace that controller panel.
3. Why does the barrier finish half operation of opening and closing?
If uses our controller panel, you only need to find resistance R37 on controller panel, and repalce it is ok.
4. When barrier closed, why is there a 5 degree angle of inclination?
the model is not good, and the gear doesn't fit each other tightly.
the barrier didn't adjust well, need to reset.
5. When barrier finish open, but it closes itself without any order control, what's the problem?
To check the loop cable first, because the loop cable maybe brokem
To check the motor sensor, if it is not set well, then reset it in the middle between two holes on sensor rod.
6. Why does the arm wave a lot when opening and closing?
The spring is very tight
The Screw touches the rubber absorption tightly, need to reset again.
7. Rubber linning installation suggestion:
It is good use for fast speed, like 0.6s, 1s, 1.8s and 3s.
The place with many vehicles come and go, like shopping center, carpark area.
8. Can you accept OEM/ODM order?
Absolutely, we are manufacturer of barrier gate, with 7 years researching and developing experience.
If you have any question, please contact us freely!
Sales representatives: Keira
Whatsapp: +86 18507481610
Skype: zimin1314
Email: keira@wonsunbarrier.com
Wechat: Keira_Xia
10 Million Lifetime DC24V Servo Motor Toll Barrier Gate Parking Lot System Factory Price
10 Million Lifetime DC24V Servo Motor Toll Barrier Gate Parking Lot System Factory Price
10 Million Lifetime DC24V Servo Motor Toll Barrier Gate Parking Lot System Factory Price
Your message must be between 20-3,000 characters!
