China Shenzhen Wonsun Machinery & Electrical Technology Co. Ltd Company News

10 Million Lifetime DC24V Servo Motor Toll Barrier Gate Parking Lot System Factory Price     DZ-138 specifications:   DZ-138 barrier gate V06T V09T Max Boom Length and Diameter 2500mm, Ф75mm 3000mm, Ф75mm Open/Close Time 0.6sec 0.9sec,2.5sec,4.5sec Power Supply 24/100/240VAC,50/60Hz 24/100/240VAC,50/60Hz Power Consumption max.150W 100w Machine Case Varnished 2.0mm steel plate Varnished 2.0mm steel plate Machine Case Size(W*D*H) 342*312*959mm 342*312*959mm Net Weight 43kg 42.6kg Operating Temperature Range℃ -45℃~+85℃ -45℃~+85℃ Driving Method Servo motor Servo motor Protection System(IP) 54 54 Insulation Class F F Relative Humidity ≤90% ≤90% Motor No-load Speed 3000r/min 3000r/min Remote Control Distance ≤100m (open, sunny weather) ≤100m (open, sunny weather) Output Torque 1.2N.M*140=160N.M 0.86N.M*140=120N.M Running Noise＜ 45dB 45dB Surface Treatment Outdoor metal powder electrostatic spraying Outdoor metal powder electrostatic spraying DZ Controller     Voltage(±10%) 100-240 volt 100-240 volt Frequency(Hz) 50-60 50-60 Max Power Consumption(watt) 8 8 Fuse F5AH F5AH Control Voltage 24V DC/max.3000mA 24V DC/max.3000mA Input-end Number 8 8 Open Collector Output Number 2 2 Zero Level Reversal Relay Number 3 3 Operating Temperature Range℃ -45℃~+85℃ -45℃~+85℃ Protection System(IP) 20 20 Weight(gram) 450gram 450gram Dimension mm(L-W-H) 158*126*55   Functions and Features: 1. Gate automatically open when power off, no clutch design, no need human intervention. When power on, gate automatically reset, restore to the gate closing state, truly unattended, fire safety standards. If special requirement, manual operation is required when power off, operating arm open and close manually also can be realized by setting up control board DIP switch, which ensure that the system can be used at any time. 2. The use of Single Compression Balance Spring device, good regulation, no noise, indefatigable, not easy to break, safe and reliable. 3. A variety of input and output modes can be selected, normally open normally closed are optional. 4. Arm opening angle can be adjusted from 60 to 90 degrees, 10 degrees resolution, suitable for eaves prominent place to install. 5. Closing speed can be adjusted. 6. Barrier gate up &down signal relay switch output. 7. Barrier gate running state: OK signal output indicating that the gate is working properly. 8. Barrier gate operation abnormal alarm signal output. 9. R&G Traffic light relay switch signal output. 10. External loop detector signal anti-smashing interface, infrared sensor signal anti-smashing interface. 11. Count mode interface. 12. Arm Open priority anti-smashing function. No matter the current gate in what state, the operator through the triple push button, software or remote control to issue an open command, the gate will give priority to the implementation of the opening action. 13. Barrier with anti-collision protection function, when the vehicle hits the gate arm, arm can be swing out to avoid damage to the vehicle, and barrier gate machine. 14. Delay closed selection function. 15. High-sensitivity arm auto reverse function (intensity can be adjusted). 16. Parking system interface. 17.RS485 or RS232 network communication control up &down interface (no need to install communication module) 18. Anti-collision alarm signal interface. 19. Adjustable speed port (from 0.9s to 10 s) 20. High-strength precision cast steel, industry moving parts beyond the industry quality     Program 1 The barrier gate can be controlled by two buttons and a short time signal impulse is enough to open barrier gate. Wiring Connection: turn on the GND and COM, Opening: turn on the 24V with UP Closing: turn on the 24V with Down Additional safety devices can be connected to the infrared signal input, vehicle detector signal input (loop detector).   Program 2 The barrier gate can be closed and opened by remote controller Wiring Connection: connecting the receiver GND(COM) to COM of controller Remote-up is for opening and Remote-down is for closing. Opening: connecting the receiver’s up level signal(5~24V) to the remote-up Closing: connecting the receiver’s down level signal(5~24V) to the remote-down Additional safety devices can be connected to the infrared signal input, vehicle detector signal input (loop detector).   If remote control receiver is non-electric relay signal, connection as bellows: Wiring Connection: turn on the GND and COM, Opening: turn on the +24V with Remote-up Closing: turn on the +24V with Remote-down Additional safety devices can be connected to the infrared signal input, vehicle detector signal input (loop detector).     FAQ: 1. When barrier finish closing, why does the arm open itself slowly? the spring is too tight, you need release the spring a little, then test it again. see whether the main crank touch the triangle tightly or not, if tightly, adjust it. reset the balance position and the electrical limit switch. 2. Why does the controller panel operate with "Di Di Di" abnormal noises? As for this, it means the resistance on controller board is broken, if you have professional tools to check, then replace that broken resistance, if not, replace that controller panel. 3. Why does the barrier finish half operation of opening and closing? If uses our controller panel, you only need to find resistance R37 on controller panel, and repalce it is ok. 4. When barrier closed, why is there a 5 degree angle of inclination? the model is not good, and the gear doesn't fit each other tightly. the barrier didn't adjust well, need to reset. 5. When barrier finish open, but it closes itself without any order control, what's the problem? To check the loop cable first, because the loop cable maybe brokem To check the motor sensor, if it is not set well, then reset it in the middle between two holes on sensor rod. 6. Why does the arm wave a lot when opening and closing? The spring is very tight The Screw touches the rubber absorption tightly, need to reset again. 7. Rubber linning installation suggestion: It is good use for fast speed, like 0.6s, 1s, 1.8s and 3s. The place with many vehicles come and go, like shopping center, carpark area. 8. Can you accept OEM/ODM order? Absolutely, we are manufacturer of barrier gate, with 7 years researching and developing experience. If you have any question, please contact us freely! Sales representatives: Keira Whatsapp: +86 18507481610 Skype: zimin1314 Email: keira@wonsunbarrier.com Wechat: Keira_Xia 10 Million Lifetime DC24V Servo Motor Toll Barrier Gate Parking Lot System Factory Price 10 Million Lifetime DC24V Servo Motor Toll Barrier Gate Parking Lot System Factory Price 10 Million Lifetime DC24V Servo Motor Toll Barrier Gate Parking Lot System Factory Price

Free Maintenance 1.5sec Vehicle Barrier Gate 24V DC Brushless Backup Battery Speed Adjustable With Curved Arm     Contact Keira Freely! Email: keira@wonsunbarrier.com Whatsapp:+86 185 0748 1610 Skype: zimin1314     Safety Precautions   To ensure your safe operation, please strictly in accordance with the provisions of this manual. To avoid personal injury, it is strictly forbidden to open the door or cover when barrier working. The barrier housing must be connected to the ground to prevent inductive electric shock. It is strictly forbidden to stand, walk or place objects under the boom/ arm when barrier working. The boom/arm and the spring have been matched to the balance state before goods leave out our factory. To avoid the danger of the balance being lost, the length and weight of the boom/arm can not be increased or decreased at random. If you need to change it, please ask the professional for advice.   Product Overview   This product adopts the latest mold design technology, mold die-casting manufacturing technology, brushless control speed technology, and can be quickly interchanged, no clutch design, more reliable quality and more convenient use. The movement adopts two-stage worm gear transmission and curved crank arm three- link structure, and the landing rod is fast and stable. Easy maintenance and long service life .     Technical parameters   1 Working temperature(motor): -35℃~+85℃ 2 Rated voltage:DC24V 3 Running speed:1.5s-8s 4 Rated current:8.58A 5 Rated power:140W 6 No-load speed:1850rpm 7 Rated speed:1400rpm 8 Output Power:56.8N.m 9 Relative humidity:≤90% 10 Remote control distance:≤100M(in the open place) 11 IP Degree:IP44 12 Max length of arm:6M     Arm length speed comparison table   Menu code Number Menu code name Defaults unit Remarks H00-00 25-95 Open speed adjustment 40   Corresponding PWM duty cycle 25%-95%, step size is 1 H00-01 25-95 Close speed adjustment 40   Corresponding PWM duty cycle 25%-95%, step size is 1 H00-02 5-40 Open in place decelerate angle 35   The larger the angle value, the less likely it is to shake the arm when it is in place. H00-03 5-40 Close in place decelerate angle 35   The larger the angle value, the less likely it is to shake the arm when it is in place. H00-04 1-20 Open accelerate adjustment 10 ms The smaller the number, the faster the speed H00-05 1-20 Close accelerate adjustment 10 ms The smaller the number, the faster the speed H00-06 1-30 Open in place angle 2 degree step size is 1 H00-07 1-30 Open in place angle 1 degree step size is 1 H00-08 7-13 Auto reverse force adjustment 10 A step size is 1 H00-09 0-90 Delay closing adjustment 0 Sec step size is 100；0 is not closing automatically,,Other value will be closing automatically;This parameter is for when there is no loop detector signals and non-automatic operation occasions H00-10 10-50 Self-check speed adjustment 30   Corresponding PWM duty cycle 10%-50%, step size is 1 H00-11 0-2 Self-check mode 0   0:no operate automatically；1:operate automatically,remove after power off；2:operate automatically,Power failure memory H00-12 0-5 Self-lock force adjustment(Invalid) 3     H00-13 1-20 Motor deceleration time when paused 5   The larger the setting, the longer the pause time will take H00-14 0-1 The default direction of operation after self-test 0   0:Closing,1:opening H00-15 1-10 Number of pole pairs(Invalid) 4   Only used to correctly display motor speed values H00-16 1-32 RS485communication address 1   Up to 32 slaves can be connected H00-17 0-2 RS485communication rate 0   0:9600,1:19200,2:38400；Change the parameter and will be valid after power on again. H00-18 0-1 If self-test after power is on 1   0:no self-test after power on,1:self-test after power on H00-19 0-3 Manual self-test adjustment 2   0:Manually invalid,1:Keyboard SET button,2:remote control valid,3,Keyboard SET button and remote control both valid H00-20 0-15 Monitoring parameter setting index 7   7,operation times(ms):0~9000 8,Cumulative operation times:0`99999999 9,automatically operation times :0~99999999 10,Collision times:0~99999999 11,Closing in place times:0~99999999 12,Power-on time (minutes):0~99999999 13,power-on times:0~99999999 14,Input port status:Binary display 15,Error code:0~7 H00-21 0-3 reset 0   1:rest adjustment H00-22 0-1 LED output mode 0   0:Do not flash alternately during operation；1:Allow flashing       FAQ   1-Can you install using loop detector or pressure sensor on it? Yes,the stanadard advertising barrier gate have loop detector and pressure sensor.   2-How about the guarantee and after sale service? We have 1 year quality guarantee, We own well tranied and passional sales & aftersale services who can speak fluent English language.   3-How long is the leading time? For standard item 10-50 sets:5 working days 50-100 sets:7-10 working days 200-500 sets:10-15 working days For special item, or need custom design package or logo, need 3-10 working days longer.   4-How about the payment terms? TT,western union,our company already joined the trade assurance,it will highly protect your order security.   5-How do you send the products to me,how long? As our products are big volume,and heavy duty, we suggest you to ship by sea. You can also choose your own shipping forwarder. it normally takes 7-60 days depend on different countries.   6-What is the package of the barrier gate? Inside with a carton package.Then outside,there are wooden crate package.     Contact Keira Freely! Email: keira@wonsunbarrier.com Whatsapp:+86 185 0748 1610 Skype: zimin1314 Wechat: Keira_Xia 1.5sec Vehicle Barrier Gate 24V DC Brushless Backup Battery Speed Adjustable With Curved Arm 1.Free Maintenance 1.5sec Vehicle Barrier Gate 24V DC Brushless Backup Battery Speed Adjustable With Curved Arm Free Maintenance 1.5sec Vehicle Barrier Gate 24V DC Brushless Backup Battery Speed Adjustable With Curved Arm Free Maintenance 1.5sec Vehicle Barrier Gate 24V DC Brushless Backup Battery Speed Adjustable With Curved Arm

Economical DC 24V Brushless Motor Vehicle Barrier Gate With 12V Backup Battery Solar Panel​ Technical parameters 1 Working temperature(motor): -35℃~+85℃ 2 Rated voltage:DC24V 3 Running speed:1.5s-8s 4 Rated current:8.58A 5 Rated power:140W 6 No-load speed:1850rpm 7 Rated speed:1400rpm 8 Output Power:56.8N.m 9 Relative humidity:≤90% 10 Remote control distance:≤100M(in the open place) 11 IP Degree:IP44 12 Max length of arm:6M Features The running speed can be adjusted from 1.5s to 8s Open the barrier gate by motor wheel when power off ,automatically reset after power on Curved crank arm three- link movement structure, the operation is stable Wireless remote control control open/close Auto reverse function(force adjustable) Infrared photocells connector is available Loop detector connector is available. Well-integrated with car parking system equipment,with wire control(must be switch signal) Connector for traffic light(AC220V,power less than 40W) Offering dry contact signal for car parking system(COM,NC,NO) Auto-delay when closing(adjustable) RS485 or CAN network communication interface(no need to install module) Counting interface 24V backup battery interface(Can be charged by using solar energy) Electrical installation, wiring diagram 1 All the electrical connections are done before delivery and please do not change it randomly.The necessity is to connect the AC220V power and grounding connection. 2 Traffic light connector:it can connect power no more than 40W. 3 Infrared photocells an-hit connector: connect the switch signal for receiver output. 4 Loop detector connectors:it supports both externally and internally loop detector(only one way can be chosen). If external type is selected,just connect the switch signal for loop detector output. If the internal type is selected,need connect the wire signal to vehicle detector wire interface. 5 Car parking system connectors: connect the system switch signal to this connector,then it can control the barrier gate operation. 6 Limit switch signal of up/down:with output COM,NO,NC,it monitoring the status of the barrier gate. 7 RS485 connector:after chosen the options RS485 module,it can manage MAX 15 pieces of barrier gates by PC software.   Product Maintenance 1 Keep the barrier gate clean 2 Check the joints ever month in case of any loose parts. 3 Check the spring elasticity after the barrier gate running 3000 times. 4 Check the easily worn-out parts(like the spring,limit switch),every half year and renew it. 5 Remote control distance will be shortened or not work in case like big object screening,battery exhausting,extreme weathers. Arm length speed comparison table   Menu code Number Menu code name Defaults unit Remarks H00-00 25-95 Open speed adjustment 40   Corresponding PWM duty cycle 25%-95%, step size is 1 H00-01 25-95 Close speed adjustment 40   Corresponding PWM duty cycle 25%-95%, step size is 1 H00-02 5-40 Open in place decelerate angle 35   The larger the angle value, the less likely it is to shake the arm when it is in place. H00-03 5-40 Close in place decelerate angle 35   The larger the angle value, the less likely it is to shake the arm when it is in place. H00-04 1-20 Open accelerate adjustment 10 ms The smaller the number, the faster the speed H00-05 1-20 Close accelerate adjustment 10 ms The smaller the number, the faster the speed H00-06 1-30 Open in place angle 2 degree step size is 1 H00-07 1-30 Open in place angle 1 degree step size is 1 H00-08 7-13 Auto reverse force adjustment 10 A step size is 1 H00-09 0-90 Delay closing adjustment 0 Sec step size is 100；0 is not closing automatically,,Other value will be closing automatically;This parameter is for when there is no loop detector signals and non-automatic operation occasions H00-10 10-50 Self-check speed adjustment 30   Corresponding PWM duty cycle 10%-50%, step size is 1 H00-11 0-2 Self-check mode 0   0:no operate automatically；1:operate automatically,remove after power off；2:operate automatically,Power failure memory H00-12 0-5 Self-lock force adjustment(Invalid) 3     H00-13 1-20 Motor deceleration time when paused 5   The larger the setting, the longer the pause time will take H00-14 0-1 The default direction of operation after self-test 0   0:Closing,1:opening H00-15 1-10 Number of pole pairs(Invalid) 4   Only used to correctly display motor speed values H00-16 1-32 RS485communication address 1   Up to 32 slaves can be connected H00-17 0-2 RS485communication rate 0   0:9600,1:19200,2:38400；Change the parameter and will be valid after power on again. H00-18 0-1 If self-test after power is on 1   0:no self-test after power on,1:self-test after power on H00-19 0-3 Manual self-test adjustment 2   0:Manually invalid,1:Keyboard SET button,2:remote control valid,3,Keyboard SET button and remote control both valid H00-20 0-15 Monitoring parameter setting index 7   7,operation times(ms):0~9000 8,Cumulative operation times:0`99999999 9,automatically operation times :0~99999999 10,Collision times:0~99999999 11,Closing in place times:0~99999999 12,Power-on time (minutes):0~99999999 13,power-on times:0~99999999 14,Input port status:Binary display 15,Error code:0~7 H00-21 0-3 reset 0   1:rest adjustment H00-22 0-1 LED output mode 0   0:Do not flash alternately during operation；1:Allow flashing     Wonsun is a professional manufaturer for barrier gate, boom barrier, sliding gate motor. If any interest, please contact me freely. Email: keira@wonsunbarrier.com Skype: zimin1314 Whatsapp: +86 185 0748 1610 Wechat: Keira_Xia Economical DC 24V Brushless Motor Vehicle Barrier Gate With 12V Backup Battery Solar Panel Economical DC 24V Brushless Motor Vehicle Barrier Gate With 12V Backup Battery Solar Panel Economical DC 24V Brushless Motor Vehicle Barrier Gate With 12V Backup Battery Solar Panel

Good news! Our barrier not only suitable for indoor as well as outdoor parking area at airport, shopping mall, warehouse and, hotel in, factories, highway toll-gate,  condominium,  car rental companies, any auto-pay tickets parking or access control system,  but also used together with disinfector at the gate of stock breeding farm and poultry farm.