Company News About DC 24V Servo Motor Security Barrier Gate Parking Lot System 10 Million Lifetime
10 Million Lifetime DC24V Servo Motor Toll Barrier Gate Parking Lot System Factory Price
DZ-138 specifications:
| DZ-138 barrier gate | V06T | V09T |
| Max Boom Length and Diameter | 2500mm, Ф75mm | 3000mm, Ф75mm |
| Open/Close Time | 0.6sec | 0.9sec,2.5sec,4.5sec |
| Power Supply | 24/100/240VAC,50/60Hz | 24/100/240VAC,50/60Hz |
| Power Consumption | max.150W | 100w |
| Machine Case | Varnished 2.0mm steel plate | Varnished 2.0mm steel plate |
| Machine Case Size(W*D*H) | 342*312*959mm | 342*312*959mm |
| Net Weight | 43kg | 42.6kg |
| Operating Temperature Range℃ | -45℃~+85℃ | -45℃~+85℃ |
| Driving Method | Servo motor | Servo motor |
| Protection System(IP) | 54 | 54 |
| Insulation Class | F | F |
| Relative Humidity | ≤90% | ≤90% |
| Motor No-load Speed | 3000r/min | 3000r/min |
| Remote Control Distance | ≤100m (open, sunny weather) | ≤100m (open, sunny weather) |
| Output Torque | 1.2N.M*140=160N.M | 0.86N.M*140=120N.M |
| Running Noise＜ | 45dB | 45dB |
| Surface Treatment | Outdoor metal powder electrostatic spraying | Outdoor metal powder electrostatic spraying |
| DZ Controller | ||
| Voltage(±10%) | 100-240 volt | 100-240 volt |
| Frequency(Hz) | 50-60 | 50-60 |
| Max Power Consumption(watt) | 8 | 8 |
| Fuse | F5AH | F5AH |
| Control Voltage | 24V DC/max.3000mA | 24V DC/max.3000mA |
| Input-end Number | 8 | 8 |
| Open Collector Output Number | 2 | 2 |
| Zero Level Reversal Relay Number | 3 | 3 |
| Operating Temperature Range℃ | -45℃~+85℃ | -45℃~+85℃ |
| Protection System(IP) | 20 | 20 |
| Weight(gram) | 450gram | 450gram |
| Dimension | mm(L-W-H) | 158*126*55 |
Functions and Features:
1. Gate automatically open when power off, no clutch design, no need human intervention. When power on,
gate automatically reset, restore to the gate closing state, truly unattended, fire safety standards. If special
requirement, manual operation is required when power off, operating arm open and close manually also can
be realized by setting up control board DIP switch, which ensure that the system can be used at any time.
2. The use of Single Compression Balance Spring device, good regulation, no noise, indefatigable, not easy to break, safe and reliable.
3. A variety of input and output modes can be selected, normally open normally closed are optional.
4. Arm opening angle can be adjusted from 60 to 90 degrees, 10 degrees resolution, suitable for eaves prominent place to install.
5. Closing speed can be adjusted.
6. Barrier gate up &down signal relay switch output.
7. Barrier gate running state: OK signal output indicating that the gate is working properly.
8. Barrier gate operation abnormal alarm signal output.
9. R&G Traffic light relay switch signal output.
10. External loop detector signal anti-smashing interface, infrared sensor signal anti-smashing interface.
11. Count mode interface.
12. Arm Open priority anti-smashing function. No matter the current gate in what state, the operator through the triple
push button, software or remote control to issue an open command, the gate will give priority to the implementation of the opening action.
13. Barrier with anti-collision protection function, when the vehicle hits the gate arm, arm can be swing out to avoid
damage to the vehicle, and barrier gate machine.
14. Delay closed selection function.
15. High-sensitivity arm auto reverse function (intensity can be adjusted).
16. Parking system interface.
17.RS485 or RS232 network communication control up &down interface (no need to install communication module)
18. Anti-collision alarm signal interface.
19. Adjustable speed port (from 0.9s to 10 s)
20. High-strength precision cast steel, industry moving parts beyond the industry quality
Program 1
The barrier gate can be controlled by two buttons and a short time signal impulse is enough to open barrier gate.
Wiring Connection: turn on the GND and COM,
Opening: turn on the 24V with UP
Closing: turn on the 24V with Down
Additional safety devices can be connected to the infrared signal input, vehicle detector signal input (loop detector).
Program 2
The barrier gate can be closed and opened by remote controller
Wiring Connection: connecting the receiver GND(COM) to COM of controller Remote-up is for opening and Remote-down is for closing.
Opening: connecting the receiver’s up level signal(5~24V) to the remote-up
Closing: connecting the receiver’s down level signal(5~24V) to the remote-down
Additional safety devices can be connected to the infrared signal input, vehicle detector signal input (loop detector).
If remote control receiver is non-electric relay signal, connection as bellows:
Wiring Connection: turn on the GND and COM,
Opening: turn on the +24V with Remote-up
Closing: turn on the +24V with Remote-down
Additional safety devices can be connected to the infrared signal input, vehicle detector signal input (loop detector).
2. Why does the controller panel operate with "Di Di Di" abnormal noises?
3. Why does the barrier finish half operation of opening and closing?
4. When barrier closed, why is there a 5 degree angle of inclination?
5. When barrier finish open, but it closes itself without any order control, what's the problem?
6. Why does the arm wave a lot when opening and closing?
7. Rubber linning installation suggestion:
8. Can you accept OEM/ODM order?
If you have any question, please contact us freely!
Sales representatives: Keira
Whatsapp: +86 18507481610
Skype: zimin1314
Email: keira@wonsunbarrier.com
Wechat: Keira_Xia
10 Million Lifetime DC24V Servo Motor Toll Barrier Gate Parking Lot System Factory Price
10 Million Lifetime DC24V Servo Motor Toll Barrier Gate Parking Lot System Factory Price
10 Million Lifetime DC24V Servo Motor Toll Barrier Gate Parking Lot System Factory Price
