|Product Name:||0.9s 3m DC PMSM Motor Gate Barrier Highway Barrier Toll Gate Barrier||Machine Case:||Varnished 2.0mm Steel Plate|
|Working Environment Temperature:||-40 ℃ ~ +85 ℃||Operation Time:||0.3,0.6,0.9,2,4sec|
|Arm Type::||Straight, Folding, Fencing||Color::||Yellow, Orange, Grey-black|
auto barrier gate system,
security barrier gate
0.9s 3m DC PMSM Motor Gate Barrier Highway Barrier Toll Gate Barrier
The DZ-1XX servo barrier gate series, which manufactured by our company, adopts international advanced
technology, mechanical and electrical integrated design. Planet gear drive, high torque, un-blocked, oil tight,
no noise, automatically Self-locked when power off, with 10 million operation times. The motor uses the
DC 24V permanent magnet synchronous motor (PMSM motor), apply to the global voltage, high-speed
operation and rapid response, frequent positive &negative operation in 24 hours does not heat, speed
time can be adjusted based on the vehicle flow and arm length, safe and reliable. The series servo barrier
gate is free-debugging and free-maintenance, achieve the fully automation and intelligent ,and the barrier
arm open/close is fast and smooth, easy to use and safe.
|DZ-138 barrier gate||V06T||V09T|
|Max Boom Length and Diameter||2500mm, Ф75mm||3000mm, Ф75mm|
|Machine Case||Varnished 2.0mm steel plate||Varnished 2.0mm steel plate|
|Machine Case Size(W*D*H)||342*312*959mm||342*312*959mm|
|Operating Temperature Range℃||-45℃~+85℃||-45℃~+85℃|
|Driving Method||Servo motor||Servo motor|
|Remote Control Distance||≤100m (open, sunny weather)||≤100m (open, sunny weather)|
|Surface Treatment||Outdoor metal powder electrostatic spraying||Outdoor metal powder electrostatic spraying|
|Voltage(±10%)||100-240 volt||100-240 volt|
|Max Power Consumption(watt)||8||8|
|Control Voltage||24V DC/max.3000mA||24V DC/max.3000mA|
|Open Collector Output Number||2||2|
|Zero Level Reversal Relay Number||3||3|
|Operating Temperature Range℃||-45℃~+85℃||-45℃~+85℃|
Servo Motor Barrier Advantages:
|1. Gate automatically open when power off, no clutch design, no need human intervention. When power on, gate automatically reset, restore to the gate closing state, truly unattended, fire safety standards. If special requirement,manual operation is required when power off, operating arm open and close manually also can be realized by setting up control board DIP switch, which ensure that the system can be used at any time.|
|2. The use of Single Compression Balance Spring device, good regulation, no noise, indefatigable, not easy to break, safe and reliable.|
|3. A variety of input and output modes can be selected, normally open normally closed are optional.|
|4. Arm opening angle can be adjusted from 60 to 90 degrees, 10 degrees resolution, suitable for eaves prominent place to install.|
|5. Closing speed can be adjusted.|
|6. Barrier gate up &down signal relay switch output.|
|7. Barrier gate running state: OK signal output indicating that the gate is working properly.|
|8. Barrier gate operation abnormal alarm signal output.|
|9. R&G Traffic light relay switch signal output.|
|10. External loop detector signal anti-smashing interface, infrared sensor signal anti-smashing interface.|
|11. Count mode interface.|
|12. Arm Open priority anti-smashing function. No matter the current gate in what state, the operator through the triple push button, software or remote control to issue an open command, the gate will give priority to the implementation of the opening action.|
|13. Barrier with anti-collision protection function, when the vehicle hits the gate arm, arm can be swing out to avoid damage to the vehicle, and barrier gate machine.|
|14. Delay closed selection function.|
|15. High-sensitivity arm auto reverse function (intensity can be adjusted).|
|16. Parking system interface.|
|17.RS485 or RS232 network communication control up &down interface (no need to install communication module)
MPORTANT: The input control signal is divided into normally open input mode (NO)and normally close
input mode(NC). NC is recommended. Put the DIP switch 1 of the 8-digit DIP switch to ON that is the normally
close input mode! When in the Normally closed input mode, the input signal is open circuit type and valid.
The default is OFF, normally open mode. And the vehicle detector signal input (loop detector) and the photocell
infrared signal input are normally closed signal mode, please use the detector with normally close interface.
1. NO/NC mode selection, in the dip switch 1, ON for NC, OFF for NO.
2. Self-locking when power off or gate automatically open selection. In dip switch 2, ON is for automatic opening
when power off;
3. Automatic reverse or stop selection when meets external obstacle. In dip switch 3, ON is for automatic
stop and OFF is for automatic reversing;
4. Auto closing speed adjustment selection, in the dip 4, 0.9s and 1.3s for option. ON is for 0.3s.
5. Delay automatic closed selection. Dip switch5,6,7,8 are for it and the delaying time is 1s,2s,3s,4s,5s,
8s,10s,15s,20s,25s,30s,35s,40s,50s,60s for option.
6. The boom angle adjustment, suitable for some areas that the boom can’t reach the vertical position
caused by obstacle. Adjustable for 60°, 70°, 80° and 90°. And the dip switch is another independent one (1 2 switch).
7. Maintenance mode switch, convenient for possible repairing and adjusting.
8. RS485 interface, can connect with computer, check the barrier gate state and alarm information.
9. Parking lot open/close control signal and remote control open/close signal are separate. Arm opening
have memory function, Number of pulse arm opening, and closed after number of cars (must be equipped with a vehicle detector)
10. Emergent stop input signal function.
11. Arm swing out signal input function.
12. Alarm information output function.
13. Barrier gate OK signal output function.
14. All input ports are optoelectronic isolation, the input voltage range is DC5 ~ 24V
15. Vehicle detector signal input and infrared signal input, that is, use the output COM, NC of the loop detector
(normally the No.4 and No.11, specially related with detector, the barrier gate not respond to closing command
when the coil is not connected).The infrared detector uses the NPN type.
1. Two year’s free servicing is supplied (not including the arm and remote controller). In the condition of complying with
the operating instruction, without the unauthorized maintenance of the parts and the machine have no obvious
mechanical damage, we will provide a quality assurance for the barrier gate product from the date of use for a period
of two years or from the date of shipment up to three years including all mechanical and electronic components other
than special consumables.
2.Lifetime charged servicing is offered.
3.Technology servicing is supplied.
*The following situations are charged for servicing (or replacement):
1.Broken by wrong installation;
2.Broken by improper voltage;
3.The surfaces of the system destroyed by wrong installation or use.
4.Broken by natural disaster.
6.Servicing items out of the promises.
If you have any question, please contact us freely!
Sales representatives: Keira
Whatsapp: +86 18507481610
Contact Person: Keira Xia